What Is Yield Photon Flux (YPF)? Why It Differs from PPF
PPF treats a blue photon and a red photon as identical. Plants do not. YPF is the metric that admits the difference, and it is the reason two fixtures with the same PPF can grow different crops.
Photosynthesis is driven by photons rather than by energy, which is why horticultural lighting moved from watts and lumens to photon metrics. The most familiar of those metrics, PPF, counts every photon between 400 and 700 nanometres as though each one were worth the same. That convention made specifications comparable, and it is still what appears on test reports. It also hides a measured fact: an absorbed photon at 620 nm yields more photosynthesis than an absorbed photon at 450 nm.
YPF, yield photon flux, is the metric built to reflect that fact. It is not new, and it is not a marketing invention; it comes out of action-spectrum measurements made on single leaves in the early 1990s and is still the standard reference when spectrum quality has to be expressed as one number.
What YPF weights, and over what range
YPF is a photon flux in micromoles per second, weighted by relative quantum yield and summed from 360 to 760 nm. PPF is a photon flux in the same unit, summed from 400 to 700 nm with equal weight. Both describe the output of a fixture at the source; neither describes what reaches the canopy, which is the job of the density metrics.
Two details follow from that definition and both matter in procurement. The first is that YPF extends beyond the photosynthetically active band into the far-red, because the action spectra it is built from do not fall to zero at 700 nm. The second is that the weighting was derived at low light, below roughly 150 micromoles per square metre per second on a single leaf, so it describes photochemistry near the light-limited part of the response curve rather than the light-saturated behaviour of a dense canopy.
Where the two metrics disagree
The practical difference is concentrated in the blue and cyan region. Under the YPF weighting, photons between 600 and 630 nm can drive 20 to 30 percent more photosynthesis than photons between 400 and 540 nm, per photon absorbed. A fixture that reaches its PPF number with a large blue component therefore carries a YPF figure that is noticeably lower than a red-dominant fixture of the same PPF.
That is not an argument against blue light. Blue regulates stomatal opening, leaf expansion, pigmentation and compact growth, and a spectrum without it produces stretched, thin-leaved plants. It is an argument against reading a single number as a quality score. PPF tells you how many photons leave the fixture; YPF tells you how those photons are distributed across a curve that approximates their usefulness; neither tells you how evenly they land on the crop.
| Metric | Unit | Range and weighting | Question it answers | Typical use |
|---|---|---|---|---|
| PPF | µmol/s | 400-700 nm, all photons equal | How many photosynthetic photons does the fixture emit per second? | Fixture specification and comparison |
| YPF | µmol/s | 360-760 nm, weighted by relative quantum yield | How much photosynthesis will those photons drive, per photon? | Spectrum quality as a single number |
| PPFD | µmol m-2 s-1 | 400-700 nm, all photons equal, per unit area | How much light arrives at a point on the canopy right now? | Layout design, hanging height, uniformity checks |
| YPFD | µmol m-2 s-1 | 360-760 nm, weighted, per unit area | How much yield-weighted light arrives at a point? | Comparing spectra at the crop, not at the source |
| DLI | mol m-2 d-1 | PPFD integrated over the photoperiod | How much light does the crop receive in a day? | Daily light budgeting, photoperiod trade-offs |
| PPE | µmol/J | PPF divided by input power | How efficiently does the fixture convert electricity into photons? | Energy cost and heat load calculations |
One number cannot carry the whole decision. A fixture can be strong on PPE, average on PPF, weak on YPF and still produce an excellent crop if its PPFD distribution matches the trellis and its spectrum supports the morphology the grower wants. The reverse is equally true.
What YPF does not tell you
Three limits are worth stating plainly, because YPF is sometimes presented as a complete replacement for PPF.
- It is a leaf-level, low-light weighting. In a canopy receiving 600 to 900 micromoles per square metre per second, the upper leaves are near light saturation while lower leaves are light-limited, and the marginal value of an extra photon is not the same at both positions. A single weighting curve cannot represent that gradient.
- It stops short of the whole spectrum story. Far-red beyond 760 nm, UV-B and the red to far-red ratio all change plant form and secondary metabolism without moving the YPF number much. Two spectra with identical YPF can produce different plant architecture.
- It is not the metric in the paperwork. Procurement documents, rebate programmes and test reports are written around PPF and PPFD. A supplier quoting only YPF is quoting a number that most buyers cannot audit against a standard test method.
How to use both numbers when specifying
The working sequence that holds up in commercial rooms is to specify PPF and PPFD first, because those are the numbers that can be verified and that determine whether the crop receives its daily light integral. Then use spectrum to decide morphology and quality targets, and treat YPF as a tie-breaker between fixtures that are close on PPF but differ in blue content.
For a leafy-green room at 12 to 16 moles per square metre per day, a broad white spectrum with a red boost typically lands within a few percent of the same YPF as a red-dominant bar of equal PPF, and the white version tends to give more compact growth. For a high-wire tomato crop where the canopy is deep and the lower leaves matter, the calculation shifts: the delivered PPFD profile down the crop and the far-red fraction become more informative than any single spectral score.
Whatever the choice, ask for measured data rather than modelled claims. A spectroradiometer scan of a production unit, taken at a stated distance and drive current, lets a buyer compute PPF, YPF and the ratios between them, and that scan is the only document that settles a disagreement about spectrum.
Frequently asked questions
Should I specify a grow light by YPF instead of PPF?
Not instead of PPF. PPF remains the metric that appears on test reports, in procurement documents and in most energy rebate programmes, and it is defined over a fixed 400-700 nm band that makes comparison straightforward. YPF is useful as a second number when two fixtures have similar PPF but very different spectra, because it shows which one puts more of those photons into wavebands that drive photosynthesis per photon.
Why does YPF extend from 360 to 760 nm when PPF stops at 700 nm?
The YPF weighting was derived from measured photosynthesis action spectra, which do not fall to zero at exactly 700 nm. Photons in the far-red region beyond 700 nm still contribute to photosynthesis, and the weighting continues to about 760 nm. Because YPF is a weighted sum rather than a count, extending the range and weighting each wavelength are parts of the same definition.
Is a higher YPF per watt always the better fixture?
No. The YPF weighting peaks in the orange-red region, so a narrowband red fixture will score well while leaving the blue and far-red ends of the spectrum thin. Crop responses such as leaf expansion, internode length and secondary metabolism depend on wavebands that the YPF curve does not reward much. Spectrum completeness, uniformity across the canopy and delivered PPFD at the crop still decide the result.
Can my PPFD meter measure YPF directly?
Usually not. A standard quantum sensor is built and calibrated to approximate the 400-700 nm PPF response, so it will read narrowband LED spectra with a systematic error that differs by wavelength. Barnes and co-workers quantified this for the sensors of their time, and the same physics applies to modern meters: the reading depends on the sensor's spectral response, not only on the light. For YPF you need either a spectroradiometer or a meter whose YPF calibration is stated.
About the publisher
XineLam is an LED lighting manufacturer based in Zhongshan, China, with 17 years of experience in LED lighting and 300+ patents in China and internationally. The company produces horticultural LED modules, bars and lamps for greenhouses, vertical farms and research rooms, and supports customers with spectrum selection, PPFD layout and measured photometric data for each fixture family.
The metric definitions and figures in this article follow the published sources listed below. Where a number depends on conditions such as distance, drive current or canopy density, those conditions are stated in the text.
Sources
- Barnes C., Tibbitts T., Sager J., Deitzer G., Bubenheim D., Koerner G., Bugbee B. (1993). Accuracy of quantum sensors measuring yield photon flux and photosynthetic photon flux. Utah State University, DigitalCommons@USU. digitalcommons.usu.edu/psc_facpub/303
- NASA Technical Reports Server. Accuracy of quantum sensors measuring yield photon flux and photosynthetic photon flux (record 20040090264). ntrs.nasa.gov/citations/20040090264
- Nelson J.A., Bugbee B. (2014). Economic Analysis of Greenhouse Lighting: Light Emitting Diodes vs. High Intensity Discharge Fixtures. PLOS ONE 9(6): e99010. journals.plos.org — pone.0099010